Signed in as:
filler@godaddy.com
WAVEPRO Air Pressure Guide
Air Pressure Info
Ideally, you should set-up your WAVEPRO boat seat pedestal with 1 - 1 1/2 inches of sag or set-in when the rider is sitting on the WAVEPRO. Use the O-ring on the pedestal neck as a guide.
Once you have adjusted the air pressure for the recommended sag or set-in and you find that the ride might be a little firm, simply let out 1 or 2 PSI of air pressure. Likewise, if it is too soft, increase the air pressure by 1 or 2 PSI.
NOTE: Air chamber pressures are sensitive to the ambient. Air pressure may vary by a couple of PSI on a 30° Fahrenheit or 17° Celsius temperature swing. Refer to the above chart to determine your PSI. Keep in mind this is only a guide. Ride at the PSI most comfortable to you.
Questions?
If you have questions, give us a call at (612) 834-4959
O - Ring
Air Pressure
Air Pressure
Should the O ring be loose on the
body of the boat seat pedestal ?
Yes, the main purpose for the O-ring is for
setting the proper PSI. it can also be used as a guide for determining how much travel your pedestal is utilizing
Air Pressure
Air Pressure
Air Pressure
How much air pressure should I use on my WAVEPRO boat seat pedestal ?
See our recommended air pressure guide above
FREQUENTLY ASKED QUESTIONS
How do I buy a Wavepro?
You can pay by credit card or PayPal on our website by clicking on the "shop" tab.
Or you can call or visit any of our dealers. You can find a list of our dealers under the "Dealer" tab on our website.
Will it work for my boat?
Our stationary boat seat pedestal will fit in any boat with the "6-bolt" circular pattern. (See image to the left)
The movable boat seat pedestal will depend on the type pedestal base that came stock in your boat. We currently offer 4 adaptors that accommodate Springfield and Attwood bases. Click below to find out more.
What size do I need?
A properly setup WAVEPRO boat seat pedestal will compress 1 to 1.5 inches when boater is seated.
So, the general rule is to measure the distance from the floor of your boat to the bottom of your seat
and add 1 to 1.5 inches.
However, the size WAVEPRO to order is dependent on the base and seat adapter and pedestal options selected.
Example: If the bottom of your current seat is 13" off the floor, you will want to order a WAVEPRO with a base and seat adapter that has a combined length of 14 - 14.5 inches.
Click below for length details.
Warranty?
We offer a full two-year warranty.
Will it work with my slider?
WAVEPRO pedestals are compatible with most Springfield sliders. Your WAVEPRO will come with two small screws on the top plate that will lock into the slider track.
Is the height of your pedestal adjustable?
Our boat pedestal lengths are not considered adjustable. You can lower the height before you ride by decreasing the PSI or raise your height by increasing the PSI. However, there is no lever to adjust the height. Adjusting PSI while riding is not recommended.
Can I install them myself?
Most definitely. Not many mechanical skills are needed. As long as you have the circular six-bolt pattern, its simple and should only take 5-10 minutes. There is an installation video on our installation page of the website.
Also, if you decide to purchase a lock after you've already purchased your pedestal, installing the locks are quite simple as well.
Can I use your pedestals in saltwater?
Yes. We have several customers who use them in the oceans, bays, gulf, and inner-coastal waterways. All WAVEPRO boat seat pedestals and components are hard coat anodized (III).
It is recommended that they are washed down with fresh water after each boat outing.
Does the pedestal come with a locking device?
The WAVERPRO boat seat pedestals can be ordered with a locking device or the locking device can be purchased separately at a later time.
How much does your pedestal weigh?
They are lightweight, ranging from 7 - 10 LBS.